## Rectifier Engineer Interview Questions & Answers

1. Question 1. What Is A Dc Power Supply?

Answer :The part of the equipment that converts ac into dc is called dc power supply.

2. Question 2. Define What Is A Rectifier?

Answer :A rectifier is a device which converts alternating current (or voltage) into unidirectional current (or voltage).

3. Electrical and Electronics Engineering Interview Questions

4. Question 3. What Is Piv Of A Diode In A Rectifier Circuit?

Answer :Peak Inverse Voltage (PIV) is the maximum possible voltage that occurs across a diode when it is reverse biased.

5. Question 4. What Is The Importance Of Peak Inverse Voltage?

Answer :If the applied voltage in reverse biased condition exceeds peak inverse voltage (PIV) rating of the diode, then the diode may get damaged.

6. Question 5. Define Why Half-wave Rectifiers Are Generally Not Used In Dc Power Supply?

Answer :The type of supply available from half-wave rectifier is not satisfactory for general power supply. That is Define why it is generally not used in dc power supply.

7. Mechanical Engineering Interview Questions

8. Question 6. Define Why Diodes Are Not Operated In The Breakdown Region In Rectifiers?

Answer :In breakdown region, a diode has a risk of getting damaged or burnt because the magnitude of current flowing through it increases in an uncontrollable manner. That is Define why didoes are not operated in the breakdown region in rectifiers.

9. Question 7. Ripple As Referred To In A Rectifier Circuit.

Answer :The ac component contained in the pulsating output of a rectifier is known as ripple.

10. Electrical Engineering Interview Questions

11. Question 8. What Is Transformer Utilization Factor?

Answer :Transformer utilization factor is defined as the ratio of power delivered to the load and ac rating of secondary of supply power transformer.

12. Question 9. The Output Of A 60hz Full-wave Bridge Rectifier Has A 60 Hz Ripple. It This Circuit Working Properly?

A full-wave rectifier with 60Hz input must have lowest ripple frequency equal to twice the input frequency i.e. 120Hz. If the ripple frequency is 60Hz, it means some diodes in the circuit are not working.

13. BHEL Interview Questions

14. Question 10. Define What Is Meant By Filter?

Answer :Filter is a device that converts pulsating output of rectifier into a steady dc level.

15. Question 11. Define Why Series Inductor And L-section Filters Cannot Be Used With Half-wave Rectifiers?

Answer :Series inductor and L-section filters cannot be used with half-wave rectifiers because operation of series inductor depends upon the current through it and needs a minimum current to flow at all times.

16. Control Systems-Electrical Engineering Interview Questions

17. Question 12. Why Capacitor Input Filter Is Preferred To Choke Input Filter?

Answer :In capacitor input filter, the dc output is much larger and ripples are less in comparison to those in choke input filter. So, capacitor input filter is preferred to choke input filter.

18. Electrical and Electronics Engineering Interview Questions

19. Question 13. Why π-filters Are Not Suitable For Varying Loads?

Answer :Voltage regulation in case of π-filters is very poor and, therefore, π-filters are not suitable for varying loads.

20. Question 14. Define Why R-c Filters Are Suitable Only For Light Loads?

Answer :R-C filters have poor voltage regulation and need adequate ventilation to dissipate the heat developed in the resistor R. Thus R-C filters are suitable only for light loads.

21. Question 15. Why Is Bleeder Resistance Employed In A Filter Circuit?

A resistance, called the bleeder resistance, is placed across the filter output, to provide flow of necessary minimum current through the choke at all time.

22. Electrical Machines Interview Questions

23. Question 16. What Is The Purpose Of Bleeder Resistance In A Rectifier Circuit Using L-c Filter?

Answer :Bleeder resistance RB is placed in parallel with the load so as to maintain a certain minimum current through the choke, even the load resistor gets open-circuited, and improves filtering action.

24. Question 17. Define What Is Meant By Voltage Regulation Of A Dc Power Supply?